Electrical installation and electrical engineering, plumbing, heating and ventilation installation

Employee protection for electrical and installation companies

Electrical and installation companies work on installations that may be live, on ladders, in shafts and ducts, and mostly at someone else's premises or construction site. Many duties therefore concern the rules for work on electrical installations, the company's own work equipment and coordination with clients.

Typical hazards and your duties

This overview lists the duties that apply most often in this industry, each with its reference in Austrian law. It does not replace identifying and assessing the hazards in your own business (§ 4 ASchG).

Work on electrical installations

Electric shocks and arc flashes usually happen when an installation has not been safely disconnected or someone switches it back on by mistake.

  • Before working in the de-energised state, clearly define the work area and follow the five safety rules: disconnect, secure against reconnection, verify absence of voltage, earth and short-circuit (always in high-voltage installations, and in extra-low and low-voltage installations if the installation could be re-energised), and cover or fence off adjacent live parts. § 12 Abs. 1 ESV 2012
  • Everyone involved in the work must be a qualified electrician or an electrically instructed person, or be supervised by such a person. An electrically instructed person is someone who has been taught by qualified electricians in such a way that they can avoid the hazards of electricity. § 12 Abs. 2 und § 1 Abs. 3 ESV 2012
  • Always keep electrical installations and equipment in a safe condition and remedy defects without delay. If that is not possible immediately, fence off or mark the danger point, for example, and inform those affected. Installations and equipment that pose an electrical hazard must not be used. § 2 Abs. 1 und 3 ESV 2012

Live working and work near live parts

When working live or next to exposed live parts, one careless movement or a slipping tool is enough.

  • Live working only by qualified electricians or electrically instructed persons with relevant special training and the required refresher training, with the necessary equipment and personal protective equipment, and only with written work instructions. Special training and written instructions may only be dispensed with if the risk assessment according to recognised engineering practice shows that safe working is nevertheless possible. § 13 Abs. 2 bis 4 ESV 2012
  • Do not carry out live working in heavy rain, poor visibility, thunderstorms, where there is a risk of fire or explosion, or when work equipment cannot be used without obstruction. § 13 Abs. 5 ESV 2012
  • Work near live parts above 50 V AC or 120 V DC only if no one can touch these parts or enter danger zones: primarily by guards, covers, enclosures or insulating sheathing, and where that is not possible, by keeping a safe distance. § 14 Abs. 1 und 2 ESV 2012
  • Young persons must not work on live parts of electrical installations above 25 V AC or 60 V DC. Measuring electrical quantities is permitted if the installation is fitted with a residual current device of no more than 30 mA. § 7 Z 9 KJBG-VO

Power tools, cable reels and residual current protection

Hammer drills, wall chasers and extension leads are used every day, often from other people's sockets at the customer's premises or on site.

  • On construction sites and at external work locations, operate portable electrical equipment from sockets of an existing building installation only if it is certain that the socket is protected by a residual current device of no more than 0.03 A, or if a portable adapter with a built-in residual current device is used. § 5 Z 3 ESV 2012
  • Preferably use cable reels with built-in overheating protection. Operate cable reels without this protection only with the cable fully unwound. § 6 ESV 2012
  • Have an electrically instructed person check the function of residual current devices using the test button, at the intervals specified by the manufacturer, otherwise at least every six months and after a fault. On construction sites, check the electrical installations for site operation and the equipment for obvious defects at least once a week. § 7 Abs. 3 Z 1 und 2 ESV 2012
  • Have electrical installations and portable Class I equipment in workplaces inspected periodically by qualified electricians. The intervals are no more than five years, and no more than one year on construction sites; the ordinance sets out further deviating intervals. Class I equipment is exempt if the risk assessment shows that it is only operated from sockets with a residual current device in accordance with Section 5 item 1 ESV 2012. § 7 Abs. 1 Z 2 und § 9 Abs. 1 und 2 ESV 2012

Ladders and work at height

Light fittings, cable trays and pipes are often installed from a ladder. Anyone climbing with full hands or leaning to the side can easily fall.

  • Use ladders as a working platform only if so little tooling and material is carried that employees can hold on securely when climbing up and down. Set up ladders on load-bearing surfaces, secured against slipping and falling over. § 34 Abs. 2 Z 1, 3 und 4 AM-VO
  • If a fall of more than 3 m from a stepladder is possible, carry out only short-term work within arm's reach from it, such as simple assembly and installation work, and only by instructed, experienced and physically fit employees. § 37 Abs. 4 AM-VO
  • Carry out only short-term work within arm's reach from leaning ladders, such as simple assembly and installation work. Where the fall height exceeds 5 m, only with personal fall protection equipment or with special measures to prevent the ladder from falling over. § 36 Abs. 6 und 7 AM-VO
  • Young persons must not work on leaning ladders with a standing height above 5 m or on stepladders with a standing height above 3 m. This is permitted after 18 months of training for instructed, experienced and physically fit young persons, under supervision and in favourable weather conditions. § 7 Z 3 KJBG-VO

Shafts, ducts and confined spaces

In shafts, ducts, crawl spaces and tanks, there may be too little oxygen or contaminated air, and rescue is difficult.

  • Draw up written operating instructions for work in small, confined or poorly ventilated spaces such as shafts, ducts or pipelines if hazards such as harmful substances, lack of oxygen, falls or pressurised pipelines cannot be ruled out. § 23a Abs. 1 AM-VO
  • Establish a written permit-to-work system with protective and rescue measures and appoint a competent person. Start work only after the permit has been issued, i.e. after special safety training and after the competent person has made sure that the measures are in place and supervision is ensured. § 23a Abs. 3 und 4 AM-VO
  • If these hazards are ruled out, at least lay down measures for monitoring and rescue and instruct the employees beforehand. Section 23a AM-VO does not apply to construction sites. § 23a Abs. 5 und 6 AM-VO

Work at customers' premises and on construction sites

Installation work mostly takes place in other companies and on construction sites, alongside other firms and with hazards the own company does not know.

  • Where employees of several employers work at the same workplace, construction site or external work location, the employers must cooperate, coordinate hazard prevention and inform each other and their employees about the hazards. § 8 Abs. 1 ASchG
  • Where necessary, the employer responsible for the workplace ensures that external employees are informed about the hazards there and given safety training, and lays down the necessary protective measures in agreement with their employer. § 8 Abs. 2 Z 1 und 3 ASchG
  • On construction sites, coordinate the work with the other employers so that hazards are avoided. Where persons have been appointed to coordinate safety and health, take their instructions and advice into account. § 8 Abs. 3 und 4 ASchG

Legal status: 21 October 2026. All references have been checked against the wording in Austria's Federal Legal Information System (RIS).

Support for your business

LEMCON.TECH works remotely for this: by video call and e-mail. This way you receive specialist support without anyone having to travel.

available

Safety training videos (subscription)

Comprehension questions for your safety training show whether it was understood (§ 14 Abs. 4 ASchG); making sure of this remains your task as the employer. Your safety briefing record supports your documentation, because safety training must be provided in a verifiable way (§ 14 Abs. 1 ASchG). The videos do not replace safety training at the specific workplace (§ 14 Abs. 3 ASchG).

  • Ladders and steps from €99.00 net Enquire now
  • Slips, trips and falls from €99.00 net Enquire now
  • Fire safety and what to do in a fire from €99.00 net Enquire now
  • Initial safety briefing for new and agency workers from €99.00 net Enquire now

Further topics:

  • Personal protective equipment
  • Using electrical equipment safely
  • First aid and emergencies
  • Skin protection and wet work
  • Safety briefing for contractors
  • Display screen work
  • Violence and assault at work
in preparation – enquire now
More about the safety training videos
available

Operating instructions for Austria and Germany

Written operating instructions for your work equipment and working substances, for display at the workplace (§ 14 Abs. 5 ASchG).

  • Standard operating instructions from a reviewed template (Austria) from €149.00 net Enquire now
  • Custom-made operating instructions (Austria) from €199.00 net Enquire now
  • Standard operating instructions from a reviewed template (Germany) from €149.00 net Enquire now
  • Custom-made operating instructions (Germany) from €199.00 net Enquire now
  • Translation of your own operating instructions with comprehension test from €39.00 net Enquire now

Typical in electrical and installation trades:

  • Working in the de-energised state: the five safety rules
  • Site distribution boards, cable reels and RCD adapters
  • Hammer drill and wall chaser
  • Leaning ladder and stepladder
  • Work in shafts and confined spaces
More about the operating instructions
available

Remote review of your risk assessment

Typical in electrical and installation trades:

  • Remote evaluation check: review of your risk assessment for the workshop, installation at customers' premises and construction sites (Sections 4 and 5 ASchG)
  • Risk assessment of working substances for assembly foam, adhesives, soldering materials or another substance or process
  • Setting up checklists and deadlines for electrical installations, power tools, residual current devices and ladders
Send an enquiry

Legal bases on this page

Questions about your industry?

Tell me what is coming up in your business.